Question: How to reset ford flex oil change?

How do you reset the oil life on a 2014 Ford Flex?

Oil Change Light Reset Ford Flex 2013 2014 2015 Procedure Turn the ignition to the “RUN” position. In the menu select “SETTINGS”, then “VEHICLE”, then “ OIL LIFE RESET %”, and finally “ RESET ”. Turn the ignition off.

How do you reset the oil change light on a 2010 Ford Flex?

Oil Change Light Reset Ford Flex 2009 2010 2011 2012 Turn the ignition to the “RUN” position. Press the “SETUP”, “ OIL LIFE % HOLD RESET = NEW” will be displayed. Press and hold “ RESET ” button for 2 seconds to reset to 100% and “ OIL LIFE SET TO 100%” will be displayed. Turn the ignition off.

How do I reset my computer after an oil change?

Insert the key into the ignition and turn it to the “on” position without starting the engine. Depress the gas pedal slowly three successive times within 10 seconds. At this point, the system should have reset . You can verify by turning the ignition off and then on again.

How do I reset my Ford oil change?

How to Reset the Oil Change Required on a Ford Vehicle Place the Ford vehicle’s transmission into park or first gear (manual). Press and release the trip/ reset button repeatedly to cycle through the available on-screen options until the display reads “ OIL LIFE = XXX% HOLD RESET .” Press and hold the trip/ reset button until the display reads “ OIL LIFE SET TO 100%.”

How do you change the oil on a Ford Flex?

Oil & Filter Change Ford Flex (2009-2019) Getting Started – Prepare for the repair. Open the Hood – How to pop the hood and prop it open. Find Oil Drain – Locate the oil drain plug underneath the vehicle. Drain Oil – Set up the workspace, drain oil and replace plug. Find Oil Filter – Locate the oil filter.

How do you reset the oil life on a 2013 Ford Flex?

Ford Flex Oil Life Reset Turn the ignition to the ON position, but do not start the engine. Use the directional pad on the steering wheel and scroll through the settings area under the heading menu. Go to Settings > Vehicle > Oil Life Reset . Push and hold OK Button until it resets to 100%

What type of oil does a Ford Flex take?

The type of oil a 2018 ford flex uses is a motorcraft synthetic blend motor oil, 5w-30 5qt.

How many quarts of oil does a 2009 Ford Flex take?

The oil capacity for the 2009 ford flex is 5.5 quarts with a filter.

Why is my change oil light still on?

If your oil light stays on even after changing your engine oil , you’re going to want to check the sensor first to rule out a malfunctioning sensor as the cause. The oil pump may not be circulating enough oil to keep the engine’s parts lubricated and functioning properly, which can in turn cause multiple engine issues.

Why won’t my change oil light go off?

To reset the oil change reminder light on your vehicle: Turn the ignition key to the run position, do not start the vehicle. Press the gas pedal fully 3 times within 10 seconds. Turn the ignition to the off position. Wait 10 seconds and start the vehicle.

Where can I get my check engine light reset?

Then put your key into the ignition and turn it three times to the “ON” position. This will clear the emissions data from the vehicle memory as well as the readiness flag data. Reconnect the positive battery cable and turn the key in the vehicle ignition. Wait one minute and the check engine light error should be gone.

How do I reset my Ford Escape?

2017-2021 Models Using the directional pad on the left side of the steering wheel, select “Settings“. Choose “Vehicle“. Select “Oil Life Reset “. Press and hold the “OK” button. Select the percentage you wish to be warned for your next oil change.

How long can I wait to change my oil after the light comes on?

How long can you drive without an oil change after the oil change light comes on ? After your car’s oil change light comes on , you should get the oil changed within the next two weeks. At most, once that light comes on , you should get the oil changed before the next 500 miles of driving.

How do you reset the oil life on a 2019 f250?

2017- 2019 Ford F-250 Change Engine Oil Soon Light Reset : Turn the ignition key to the “ON” position without starting the engine. Go to the SETTINGS menu by using ▲▼ the navigation button. Scroll and select ADVANCED SETTINGS menu. Scroll to VEHICLE menu. Scroll down to OIL LIFE RESET . Press and hold the OK button until the oil life display changes to 100 percent.

Leave a Reply