Problem: 2004 ford explorer sport trac will not start?

How do you reset the security system on a 2004 Ford Explorer?

Turn key to on position without starting car. leave in this position for 10 minutes until anti-theft light goes off. turn key off and leave in ignition for 2 minutes.

How do I get my Ford Explorer out of theft mode?

To disable anti theft then get in vehicle and close the door. put key in ignition and turn from off to run 8 times. on the eighth time leave in on position and the theft light will turn off .

Where is the starter on a 2004 Ford Explorer Sport Trac?

Starters are usually low and to the rear of the engine. The nose is over the flywheel which is between the engine and transmission. Follow the positive cable from the battery.

How do you reset the computer on a Ford Explorer?

How to Reset a Ford Explorer Computer Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board. Disconnect the negative battery terminal. Wrap the negative clamp in a towel. Leave the negative battery cable off for a minimum of five minutes. Remove the towel from the negative battery cable clamp.

How do I reset my Ford Anti theft system?

How to Reset the Anti – Theft Key Ignition on a Ford F-150 Insert your first programmed key into the car’s ignition and turn it to the “On” position. Cycle the first key back “Off,” remove it from the ignition and insert the second programmed key within 5 seconds. Cycle in “On” and “Off” and then remove the second key.

How do I get my 2002 Ford Explorer out of theft mode?

To deactivate the anti- theft system on a ford explorer use the unlock button on the remote key. unlock the driver’s door using the key and then switch the ignition switch to the on position. if that doesn’t work exit the vehicle and roll up all windows, then use the key to lock the driver’s door.

How do I get my car out of theft mode?

Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car . Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.

How do I get my car out of anti theft mode without remote?

Ways to stop a car alarm without a keyfob Check your owner’s manual. Every vehicle is different. Lock your doors. Getting into the car and locking your doors (assuming you have electric locks) might stop the alarm . Turn the car on. Turn the ignition to on and wait. Pull the fuse for the alarm . Pull the wires for your alarm . Disconnect the battery.

Can you bypass PATS system?

Can you bypass the PATS system ? Yes, there is a simple way to bypass the pats system on your own. All you need is the transponder key to trick the system . By having the transponder key, you can remove the chip inside the key and glue it to the ignition and use any key that matches the original to start up the engine.

Why is my Ford Explorer not starting?

While there are a variety of reasons your Ford Explorer won’t start , the most common 3 are a dead battery, an alternator problem , or failed starter.

How do you know if your starter bad?

What are common bad starter symptoms? Something sounds off. One of the symptoms of a bad starter is a clicking noise when you turn the key or push the start button. You’ve got lights but no action. Your engine won’t crank. Smoke is coming from your car. Oil has soaked the starter .

How can you start a car with a bad starter?

Various Ways to Start a Car with a Bad Starter Begin with Examining the Connections. Examine the Engine Ground Connection. Examine the Solenoid Cable of the Starter . Check for Corrosion. Softly Thump the Starter with a Hammer. Jump Start the Car . Push the Car to Start . Examine the Flywheel of the Engine.

Will disconnecting the battery reset the computer?

However, disconnecting the battery will not only erase diagnostic trouble codes but also erase drivability, security and radio codes in many vehicles. Locate any codes and have them and the drivability learning procedures on hand before disconnecting the battery .

How do you reset your transmission?

Procedure Reset Transmission Adaptive Learning DIY Turn the key to position 2. You should see all the dash lights come on. Press the gas pedal all the way. Wait. Turn key to OFF, position 0. Release the gas pedal. Wait 2 minutes. Start the car and drive.

How do I reset my Ford computer?

How to Reset the Ford PCM Open the hood of the Ford . Loosen the lock nut located on the negative battery cable connector with a socket and ratchet. Pull the connector off the negative battery terminal. Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.

Leave a Reply